> Compliance Standards>Military & Aerospace Standards>MIL-STD-461>Radiated Emissions>MIL-STD-461 RE101
MIL-STD-461 RE101

RE101 Purpose

Radiated Emissions, magnetic field

This requirement is applicable from 30 Hz to 100 kHz for radiated emissions from equipment and subsystem enclosures, including electrical cable interfaces. The requirement does not apply to radiation from antennas.

This test procedure is used to verify that the magnetic field emissions from the EUT and its associated electrical interfaces do not exceed specified requirements.

Test Equipment

The test equipment shall be as follows:

a. Measurement receivers

b. Data recording device

c. Loop sensor having the following specifications:

(1) Diameter: 13.3 cm

(2) Number of turns: 36

(3) Wire: DC resistance between 5 and 10 ohms

(4) Shielding: Electrostatic

(5) Correction factor: See manufacturer’s data for factors to convert measurement receiver readings to decibels above one picotesla (dBpT).

d. LISNs e. Ohmmeter

f. Signal generator

Get Application Support, Pricing, Lead Time and More: Contact Form

MIL-STD-461 RE101 There are 11 products.

Showing 1 - 11 of 11 items
  • Quick view
    • 20 Hz Frequency Minimum
    • 500 kHz Frequency Maximum
    • Type BNC Connectors
    • 50 Ω Impedance (Nominal)
    • Omnidirectional Pattern Type
    • Linear Polarization
    Request Quote
    Call for Availability
    Request Quote/More Info
    Add to Compare
  • Quick view
    $3,079.00
    • 1 kHz - 30 MHz
    • Loop Diameter: 12 inches
    • 50 Ohm Impedance
    • BNC Connector
    • 2.5 LBs
    $3,079.00
    Add to cart
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • 1 KHz - 30 MHz
    • Built for MIL-STD & CISPR 16-1-4 antenna requirements
    • Loop Diameter: 12 Inches (30cm) 
    • 50 Ohms of DC Resistance
    • BNC Connector
    • Mounting Base:1/4 X 20 Thread, Female
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • For Test Methods RE101 of MIL-STD-461F
    • RE101 of MIL-STD-461D/E/F
    • Dimensions: 5.24" diameter (13.3 cm)
    • Connector: BNC
    • Number of turns: 36
    • Wire: DC resistance between 5 and 10 Ω
    • Shielding: Electrostatic
    • Weight: 2 pounds (0.9 kg)
    • Shipping weight: 3 pounds (1.36 kg)
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • 9 KHz - 30 MHz
    • Built for MIL-STD & CISPR 16-1-4 antenna requirements
    • Loop Diameter: 22 3/8 in. (56.8 cm)
    • 50 Ohms of DC Resistance
    • BNC Connector
    • Mounting Base:1/4 X 20 Thread, Female
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • 20 Hz - 1 MHz
    • Loop Diameter: 22 3/8 inches
    • 50 Ohm Impedance
    • BNC-Type Connector
    • 2.5 LBs (1.13 kg)
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Rentals ship immediately
    • 1 Hz - 26.5 GHz
    • Real-Time Analysis up to 40 MHz
    • Quasi-peak, EMI-avg, RMS-avg and diagnostic detectors
    • Meets CISPR 16-1-1: 2010 and MIL-STD-461G EMI receiver requirements
    • Purchase a Used Keysight N9038A EMI Receiver here.
    Request Quote
    Call for Availability
    Request Quote/More Info
    Add to Compare
  • Quick view
    • 20 Hz - 2 MHz
    • Built for MIL-STD-461 RE 101 Testing
    • Loop Diameter: 5¼ in. (13.3 cm)
    • 10 Ohms of DC Resistance
    • Turns: 36 (7-41 Litz)
    • BNC Connector
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Rentals ship immediately
    • 85 MHz Bandwidth Analysis Option (Fastest Testing Possible)
    • Real-Time Analysis up to 85 MHz BW
    • Quasi-peak, EMI-avg, RMS-avg and diagnostic detectors
    • Meets CISPR 16-1-1: 2010 and MIL-STD-461F EMI receiver requirements
    • Purchase a Used Keysight N9038 EMI Analyzer here.
    Request Quote
    Call for Availability
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Receiving Loop Antenna Designed Specifically for MIL-STD-461, RE101 Testing
    • 30 Hz to 100 kHz  Frequency Range
    • Antenna Base Plate Ensures Required 7 cm Separation Between Antenna and EUT 
    • Individual Calibration per SAE ARP958 Included 
    • Three-year Standard Warranty
    • Connectors: BNC (female)
    Request Quote
    1 Unit
    Request Quote/More Info
    Add to Compare
  • Quick view
    • for Test Method RE101 of MIL-STD-461F
    • Required by Test Method RE01 in Parts 2 through 6 of MIL-STD- 461C and
    • RE101 of MIL-STD-461D/E/F
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
Showing 1 - 11 of 11 items