> Compliance Standards>Military & Aerospace Standards>MIL-STD-461>Conducted Susceptibility>MIL-STD-461 CS109
MIL-STD-461 CS109

CS109 Purpose

MIL-STD-461 CS109 Conducted Susceptibility, Structure Current, 60 Hz to 100 kHz

This test procedure is used to verify the ability of the EUT to withstand structure currents.

Test Equipment

The test equipment shall be as follows:

a. Signal generator

b. Amplifier (if required)

c. Isolation transformers

d. Current probe

e. Measurement receiver

f. Resistor, 0.5 ohm

g. Coupling transformer

Get Application Support, Pricing, Lead Time and More: Contact Form

MIL-STD-461 CS109 There are 8 products.

Showing 1 - 8 of 8 items
  • Quick view
    • Rentals Ship Same Day
    • Up to 900 watts RMS power output
    • Small signal response up to 400 kHz
    • Up to 16A at 13.5 VDC
    • Stable when driving highly capacitive loads.
    • Four-quadrant operation.
    • Use for Military and Automotive Compliance
    • 120V Input
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Powered from 120V/230VAC
    • Source and Sink (4 quadrant)
    • Drop outs and surges as fast as 1.2µs
    • Small signal response up to 1 MHz
    • 13.5 VDC at up to 28A
    • Field-selectable ±40V, 75V or 150V potential
    Request Quote
    Typically in Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Magnetic field tests and measurement DC to 250 kHz
    • Complies to all relevant EMC, Automotive and Military Standards
    • Magnetic field strength up to 1000 A/m at 1000 Hz
    • Fully automated tests with triaxial Helmholtz coil
    • Wide choice of accessories
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • 5 Hz to 1 MHz
    • Multi-Purpose Power Amplifier
    • Typical applications are magnetic immunity testing;
    • According to automotive standards or MIL-461 E or F
    • Frequency range (nominal): 5 Hz - 1 MHz
    • Gain at 8 ohm impedance: 26 dB ±3 dB
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Most compact equipment for ripple noise on ac/dc supplies and magnetic fields
    • Built-in LF signal generator
    • Built-in LF amplifier
    • Built-in LF transformer 2:
    • Built-in frequency-selective voltage and current meter
    • Built-in load resistors
    • Automatic self-calibration
    • Frequency Range: 10 Hz - 250 kHz
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Multi-purpose Power Amplifier
    • Can be used within the Frequency Range from DC to 250 kHz
    • Typical applications are magnetic immunity testing according to automotive standards or MIL-461F
    • Frequency range (nominal): DC - 250 kHz
    • Gain at 8 ohm impedance: 26 dB ±3 dB
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • One-box transformer and 0.5 ohm load assembly
    • Frequency response 10 Hz to 250 kHz
    • Secondary saturation 50 A per transformer
    • Audio power 2 x 200 W
    • Freely configurable on primary/secondary; serial, parallel, single
    • Turns ratio 2:1 step down
    • Built-in non-inductive load resistor 0.5 ohm, 250 W
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Frequency range: 1 kHz - 200 MHz
    • Transfer impedance (ZT): .001
    • Continuous signal current (CW): 50 A

    Request Quote
    Typical Lead Time 4 - 6 Weeks
    Request Quote/More Info
    Add to Compare
Showing 1 - 8 of 8 items