> Manufacturers>Com-Power

Com-Power

Quick Links

Information

Com-Power

Com-Power is a leading manufacturer of test and measurement instrumentation for electromagnetic compatibility testing (EMC). The EMC Shop has partnered with Com-Power to stock and distribute new, used and rental EMC test equipment from Com-Power.

Com-Power There are 77 products.

Subcategories

  • Com-Power EMC Antennas

    The EMC Shop stocks many Com-Power antennas and are available for rental or purchase new or used. Com-Power EMI / EMC broadband and tuned antennas cover the frequency range of 9 kHz - 40 GHz. Most electronic products are required meet the various international EMC regulatory standards before they are introduced to the market. Com-Power provides a wide range of EMI antennas and accessories. We also have the capabilities to assist you with custom EMC antennas for special applications to meet your exact needs.

  • Com-Power LISN's

    LISN stands for 'Line Impedance Stabilization Network'. Com-Power offers a line of LISNs developed for conducted emission testing according to the most commonly adopted EMC specifications like CISPR, FCC, ISO, EN, RTCA DO-160 and MIL-STD 461D. The LISN circuit is designed and constructed to meet the performance criteria given by these standards.

  • Com-Power CDN's

    Com-Power CDNs (Coupling/Decoupling Networks) are primarily used for RF conducted immunity testing per IEC 61000-4-6, which is one of the EMC (electromagnetic compatibility) phenomenon tests typically required for “CE-mark” compliance testing of commercial products.

    The EMC Shop stocks calibrated CDN's for rental or sale.

  • Com-Power Preamplifiers

    Com-Power broadband high gain preamplifiers were designed for electromagnetic interference (EMI) testing and certification. EMC test labs use preamplifiers to improve sensitivity of the test system during EMI radiated emissions measurements. Without a high gain preamplifier, signals picked by the antenna that have amplitudes below the noise floor of the test system cannot be measured. The preamplifier gain has minimum variations for the entire operating frequency range for accurate emissions measurements. The Com-Power preamplifiers were primarily intended for EMC applications. However, it can be used for other applications that require signal amplification.

  • Com-Power Absorbing Clamps

    Com-Power Absorbing Clamps to measure EMI Emissions according to CISPR 13 [EN 55013], CISPR 14 [EN 55014] and CISPR 32 [EN 55032]

    The absorbing clamps also known as ferrite clamps are used for measuring disturbance power on power input lines as well as other auxiliary I/O lines. The absorbing clamp measurement method (ACMM) is described in Clause 7 of CISPR 16-2-2.

  • Com-Power RF Current Probes

    Com-Power RF Current probes are used in EMC Testing for RF current measurements, there are two types of RF current measurements made with these current probes which are simply clamped on to the cables under test, that’s why there are also refer to “clamp on current probes”.

  • Com-Power ISN's

    Com-Power Impedance Stabilization Networks (ISN's) are required for the measurement of conducted common mode noise on Telecom Cables of Information Technology Equipment (ITE). These measurements are necessary to meet the requirements specified in CISPR 22 and CISPR 32 standards.

  • Com-Power Near Field Probes

    Com-Power near field probes have nice, compact nylon tips that allows for access into small circuitry and narrow down location of source interference to within the centimeter. The EMC Shop stocks these Com-Power near-field probe sets for rental or sale. Near-field magnetic (H-field) and electric (E-field) probes let you "sniff" around the circuits, cables, and enclosures to find the source. H-field probes use a conductive loop to detect magnetic fields produced by clock signals, serial data streams, control signals, and switching power supplies. You can often uncover the source of EMI emissions with near-field probes. 

  • Com-Power Transient Limiters

    Protect your spectrum analyzer input during conducted emissions testing with a Com-Power transient limiter.

    The following products can be used during EMC conducted emissions testing to protect the input of a spectrum analyzer. Combined in both the LIT-153 and LIT-930 Transient Limiters are a low-pass filter, high pass filter, transient suppressors and two separate 5 dB impedance matching attenuation pads; one at the input and one at the output.

per page
Showing 1 - 12 of 77 items
  • Quick view
    $319.00 Monthly

    Rent AH-118 Horn Antenna and ship today


    • Rentals Ship Same Day
    • Broadband - For sweep measurements
    • High Gain - Lower Floor Noise for Emissions
    • Individual calibration
    $319.00
    Add to cart
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Continuous, broadband output for Full spectrum measurements and analysis
    • Stable output - Repeatable measurements
    • Conducted and radiated output options - Evaluation of both conducted and radiated systems
    • 9kHz to 3.5GHz output - Applications across a broad frequency spectrum
    • Compact and portable - Comparisons between sites and environment
    • Battery powered - No power or interconnecting cable effects on measurements
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view

    • Rent the Com-Power ISN T8 here.
    • Frequency Range: 150 kHz to 30 MHz
    • For Unshielded Telecomunication Lines 1 to 4 balanced pairs
    • Complies with CISPR 16-1-2, CISPR 22/32
    • Individual Calibration Included
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • 150kHz - 30 MHz Frequency Range
    • 100 Amps Current Rating
    • Fully Compliant with CISPR 16-1-2/ANSI C63.4
    • internal cooling fan
    • Remote Switching of Line Under Test
    • Four-conductor Network appropriate for both 3Ø Delta and Wye Power Configurations
    • Three-Year Warranty
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Frequency Range 700 MHz to 18 GHz
    • Enhanced Sensitivity
    • Built in 40 dB Preamp
    • Individual Calibration
    Request Quote
    1 Unit
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Broadband - 26.5 GHz to 40 GHz
    • High Gain of 26dBi - Lower Floor Noise for Emissions
    • Linear Polarization
    • Return Loss: 30 dB (typ)
    • WR-42 Waveguide
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view

    • Rent the Com-Power ISN T8 here.
    • Frequency Range: 150 kHz to 30 MHz
    • For Unshielded Telecomunication Lines 1 to 4 balanced pairs
    • Complies with CISPR 16-1-2, CISPR 22/32
    • Individual Calibration Included
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Fully compliant to MIL-STD 461
    • Provides a near 1:1 (<0.5 dB insertion loss) 50Ω coaxial measurement port (type-N)
    • Provides a defined, stable, impedance to the Equipment Under Test (EUT)
    • Individual Calibration Included
    • Three Year Warranty
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Frequency range: 25 MHz to 300 MHz
    • Collapsible antenna elements
    • Transmit & Receive Capabilities
    • Individual Calibration
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Frequency Range: 10 kHz to 400 MHz
    • Suitable for CISPR, Mil-Std 461 & DO-160
    • Optional FCLCE-1000 Calibration Fixture for 50Ω transmission line
    • Individual calibration
    • Three-year warranty

    Purchase Com-Power CLCE-400

    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view Sale!
    • Broadband: 200 MHz to 2 GHz
    • Transmit and receive capabilities
    • Individual calibration
    • Three year warranty
    • 800 Watts of CW Power Handling
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
Showing 1 - 12 of 77 items