Impedance Stabilization Network (ISN)

Rent, buy or lease CISPR 22 Impedance Stabilization Networks (ISN). The EMC Shop stocks calibrated test equipment for ITE compliance to radio disturbances.

Impedance Stabilization Network (ISN) There are 10 products.

Showing 1 - 10 of 10 items
    • CDN Coupling/Decoupling Network & ISN Impedance Stabilization Network in One
    • Refers schematic circuit example in CISPR 22/32 Figure D.3/G.3
    • 1000BaseT and PoE application
    • Can be used as CDN for IEC/EN 61000-4-6 immunity tests
    Online only
    In Stock
    Request Quote/More Info

    • Rent the Com-Power ISN T8 here.
    • Frequency Range: 150 kHz to 30 MHz
    • For Unshielded Telecomunication Lines 1 to 4 balanced pairs
    • Complies with CISPR 16-1-2, CISPR 22/32
    • Individual Calibration Included
    Typically In Stock
    Request Quote/More Info
    • For use with one, two, three, or four unscreened balanced pairs
    • Refers schematic circuit example in CISPR 22/32 Figure D.3/G.3
    • Intended for connection to cable category 6
    • 1000BaseT and PoE application
    • Can be used as CDN for IEC/EN 61000-4-6 immunity tests
    In Stock
    Request Quote/More Info
    • For use with one, two, three, or four unscreened balanced pairs
    • Refers schematic circuit example in CISPR 22/32 Figure D.3/G.3
    • Intended for connection to cable category 3 and 5
    • 1000BaseT and PoE application
    • Changeable pin-arrangements with RJ11 and RJ45

    Rent Teseq ISN T8

    In Stock
    Request Quote/More Info
    • For use with one, two, three, or four unscreened balanced pairs
    • Refers schematic circuit example in CISPR 22/32 Figure D.3/G.3
    • Intended for connection to cable category 3 and 5
    • 1000BaseT and PoE application
    • Changeable pin-arrangements with RJ11 and RJ45
    In Stock
    Request Quote/More Info
    • For use with one or two unscreened balanced pairs
    • Refers schematic circuit example in CISPR 22/32 Figure D.2/G.2
    • Intended for connection to cable category 3 and 5
    • Changeable pin-arrangements with RJ11 and RJ45
    • Can be used as CDN for IEC/EN 61000-4-6 immunity tests
    In Stock
    Request Quote/More Info
    • ISN T8 CAT5 (LCL = 65 dB) acc. CISPR 22 edition 5.2, figure D.3.
    • For up to 4 Pairs UTP
    • Allows to perform common mode disturbance voltage measurements
    • Provides an longitudinal conversion loss of typically 65 dB at the EuT port
    • Allows to measure CAT5 devices
    In Stock
    Request Quote/More Info
    • For use with one, two, three, or four unscreened balanced pairs
    • Refers schematic circuit example in CISPR 22/32 Figure D.3/G.3
    • Intended for connection to cable category 3 and 5
    • 1000BaseT and PoE application
    • Changeable pin-arrangements with RJ11 and RJ45

    Purchase Teseq ISN T8

    In Stock
    Request Quote/More Info
    • Purchase Com-Power ISN-T8 here
    • Frequency Range: 150 kHz to 30 MHz
    • For Unshielded Telecomunication Lines 1 to 4 balanced pairs
    • Complies with CISPR 16-1-2, CISPR 22/32
    • Individual Calibration Included
    $410.00
    Typically In Stock
    Request Quote/More Info
    • Frequency Range: 150 kHz to 30 MHz
    • For disturbance measurements on a single, unshielded, balanced pair
    • Provided with Cat. 3 & Cat. 5 LCL Adapters
    • Circuit concept per figure D.1 of EN 55022: 2010+AC:2011 (CISPR 22: 2008, Edition 6.0)
    • Meets applicable requirements of EN 55022: 2010+AC:2011 (CISPR 22: 2008, Edition 6.0) and CISPR 16-1-2: 2014, Edition 2.0
    Typically In Stock
    Request Quote/More Info
Showing 1 - 10 of 10 items