1 GHz Broadband RF Preamplifiers

Quick Links

Information

Viewed products

Teseq LNA 6901 Low Noise Amplifier 9 kHz to 1 GHz View larger

Teseq LNA 6901 Low Noise Amplifier 9 kHz to 1 GHz

New

  • Frequency range: 9 kHz to 1 GHz (nominal range); 9 kHz to 2 GHz (utilizable range)
  • Gain: typ. 28 dB
  • Gain flatness: ±1 dB
  • RF-Input: N - female, 50 Ω (optional N-male)
  • RF-Output: N - male, 50 Ω (optional N-female)
  • VSWR (input): <1.5
  • Noise figure: typ. 2.8 dB (at 25°C, 100 MHz)
  • 1 dB-compression (output): +8 dBm

More details

Request Quote/More Info

Specifications

Frequency Range9 kHz to 1 GHz (nominal range); 9 kHz to 2 GHz (utilizable range)
Gain28 dB typical (±1 dB flatness)
Application/Test TypeIncrease the sensitivity of virtually all spectrum analyzers and other RF measuring instruments
Input -20 dBm (87 dBμV)
Maximum Continuous Power+8 dBm @ 1 dB compression
ConnectorN-type 50 Ohms
Dimensions28 mm x 95 mm x 27 mm
VSWRLess Than 1.5:1
Weight.27 Lb's (127 grams)

Test Equipment Description

The Teseq LNA 6901 is a low noise amplifier with typ. 28 dB of gain covering the nominal frequency range 9 kHz to 1 GHz and can be used up to 2 GHz. With its high gain and low noise figure, it will significantly increase the sensitivity of virtually all spectrum analyzers and other RF measuring instruments. All measuring instruments have a ‘noise figure’, which is a measure of how good the instrument is at measuring low level signals, the lower this figure, the better, although the lowest signal level will still be governed by the measurement bandwidth. A typical spectrum analyzer may have a noise figure of 20 dB or more, whereas a typical receiver may have a noise figure of 10 dB. The preamplifier has a noise figure of typical 2.8 dB, significantly enhancing the low level performance of such instruments, enabling signals that were previously masked by noise to be seen.

The low noise amplifier can be connected directly to the RF input (N) of the spectrum analyzer or EMI-receiver. If the LNA 6901 is used with the Teseq receiver SCR 35xx / SMR 45xx, the power supply is provided directly by the receiver via the cable LE 237. Alternatively the power supply unit PSU 6000 can be used.

Features & Specifications of Teseq LNA 6901:

  • Frequency range: 9 kHz to 1 GHz (nominal range); 9 kHz to 2 GHz (utilizable range)
  • Gain: typ. 28 dB
  • Gain flatness: ±1 dB
  • RF-Input: N - female, 50 Ω (optional N-male)
  • RF-Output: N - male, 50 Ω (optional N-female)
  • VSWR (input): <1.5
  • Noise figure: typ. 2.8 dB (at 25°C, 100 MHz)
  • 1 dB-compression (output): +8 dBm
  • Intercept point IP3 (output): typ. +25 dBm
  • Max. input (linear): -20 dBm (87 dBμV)
  • DC-power supply: 11 to 15 V
  • DC-current: approx. 100 mA
  • DC-connector: ODU-female, plus on inner conductors
  • Operating temperature range: 0° to 40°C
  • Storage temperature range: -20° to 60°C
  • Size (W x D x H) (without connectors): 27 mm x 50 mm x 27 mm
  • Size (W x D x H) (including connectors): 28 mm x 95 mm x 27 mm
  • Weight: approx. 127 g

Associated EMC Test Equipment

6 other products in the same category: