> Compliance Standards>Military & Aerospace Standards>MIL-STD-461
MIL-STD-461

Test equipment for all versions of MIL-STD-461 including Version G released Decemeber 2015.

MIL-STD-461 Emission and Susceptibility Testing Breakdown

Conducted emissions requirements are designated by CE

Radiated emissions requirements are designated by RE

Conducted susceptibility requirements are designated by CS

Radiated susceptibility requirements are designated by RS

Get Application Support, Pricing, Lead Time and More: Contact Form

MIL-STD-461 There are 134 products.

Subcategories

  • Radiated Susceptibility

    MIL-STD-461 Radiated Susceptibility Description:

    The EMC Shop stock a variety of MIL-STD-461 Radiated Susceptibility test equipment for Magnetic Field, Electric Field, and Transient Electromagnetic Field applications.

    Get Application Support, Pricing, Lead Time and More: Contact Form

  • Conducted Susceptibility

    The EMC can provide test eqipment for subcategories of MIL-STD-461; Conducted Susceptibility with applications for:

    Power Leads, Antenna Port, Intermodulation, Rejection of Undesired Signals, Cross-Modulation, Structure Current, Bulk Cable Injection, Impulse Excitation, Damped Sinusoidal Transients, Cables and Power Leads, Lightning Induced Transients, and Personnel Borne Electrostatic Discharge

    Get Application Support, Pricing, Lead Time and More: Contact Form

  • Radiated Emissions

    The EMC Shop stocks and delivers a wide array MIL-STD-461 Radiated Emissions equipment. Applications include: Magnetic Field, Electric Field,Antenna Spurious and Harmonic Outputs.

  • Conducted Emissions

    MIL-STD-461 conducted emission testing equipments for power leads, antenna terminals and more. The EMC Shop carries a variety of testing equipment for all MIL-STD-461 compliance tests.

    The conducted emissions testing for MIL-STD-461 is similar to DO-160 Conducted Emissions testing.

    CE101 Applicability

    MIL-STD-461 CE101 requirement is applicable for power leads, including returns, that obtain power from other sources not part of the EUT.

    For AC applications, this requirement is applicable starting at the second harmonic of the EUT power frequency.

    CE101 Test Procedure

    This test procedure is used to verify that electromagnetic emissions from the EUT do not exceed the specified requirements for power input leads including returns. 5.4.3.2 Test equipment. The test equipment shall be as follows:

    a. Measurement receivers

    b. Current probes

    c. Signal generator

    d. Data recording device

    e. Oscilloscope

    f. Resistor (R)

    g. LISNs

per page
Showing 25 - 36 of 134 items
  • Quick view
    • Frequency range: 20 Hz to 300 MHz
    • Transfer impedance (ZT): 1 Ohm
    • Output load impedance: 50 + j 0 Ω
    • Continuous signal current (CW): 1.5 Amps (100 Amps Peak)
    • N Type Connector
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Suitable for MIL-STD 461 CE101 and other conducted emissions testing
    • Frequency range: 20 Hz to 30 MHz
    • Transfer impedance (ZT): 1 Ohm
    • Output load impedance: 50 + j 0 Ω
    • Continuous signal current (CW): 100 Amps
    • BNC Type Connector
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Frequency range: 10 kHz to 500 MHz
    • Transfer impedance (ZT): 1.0 to 5.0 Ω above 300 kHz
    • Output load impedance: 50 + j 0 Ω
    • Continuous signal current (CW): 40 AMPS
    • Maximum power current: 200 A DC to 400 Hz
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Frequency range: 20HZ - 20 MHZ
    • Transfer impedance (ZT): 1.5Ω to 3 DB 
    • Continuous signal current (CW): 40 A
    • Connector Types- N type or BNC
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Frequency Range of 100Hz - 60MHz
    • Individually Calibrated
    • FCC, MIL-STD, VDE and TEMPEST Testing
    • High Sensitivity
    • Battery Pack and Charger
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Wide frequency range: 4kHz - 100 MHz
    • Input Power: 100 W for 30 min
    • Internal diameter: 40mm
    • External diameter: 127mm
    • High power handling
    • Ideal for automotive BCI testing to ISO 7637-3
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Frequency Range of 100Hz - 60MHz
    • Individually Calibrated (Calibration included per ARP-958)
    • FCC, MIL-STD, VDE and TEMPEST Testing
    • High Sensitivity
    • Battery Pack and Charger
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Meets specifications of IEC 61000-4-6
    • Frequency range from 10 KHz up to 230 MHz
    • Designed for automotive BCI testing
    • Low insertion loss
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • 30 Hz to 100 kHz frequency range
    • Radiating Loop and Loop Sensor
    • MIL-STD-461D/RS101 magnetic field tests
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    • 30 Hz to 100 kHz frequency range
    • Connector Type: BNC
    • Radiating Loop and Loop Sensor
    • MIL-STD-461D/RS101 magnetic field tests
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    • 9 KHz - 30 MHz
    • Built for MIL-STD & CISPR 16-1-4 antenna requirements
    • Loop Diameter: 22 3/8 in. (56.8 cm)
    • 50 Ohms of DC Resistance
    • BNC Connector
    • Mounting Base:1/4 X 20 Thread, Female
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • 20 Hz - 1 MHz
    • Loop Diameter: 22 3/8 inches
    • 50 Ohm Impedance
    • BNC-Type Connector
    • 2.5 LBs (1.13 kg)
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
Showing 25 - 36 of 134 items