Impedance Stabilization Networks (ISN's)

Impedance stabilization networks (ISN's) are similar to LISN's but used for conducted emissions measurements on signal and data lines. They differ from LISN's in that they can perform Comon-Mode impedance measurements. CISPR 22 and CISPR 32 are common standards requiring the use of an ISN.

ISN's are referred to as an asymmetric artificial network (AAN) in CISPR 16-1-2.

Impedance Stabilization Networks (ISN's) There are 31 products.

per page
Showing 13 - 24 of 31 items
    • 150 kHz – 30 MHz Frequency range (ISN)
    • 150 kHz – 80 MHz Frequency range (CDN)
    • ISN T8 CAT6 (LCL = 75 dB) acc. CISPR 22 edition 5.2
    • Figure D.3. for up to 4 pairs UTP.
    In Stock
    Request Quote/More Info
    • ISN T8 CAT5 (LCL = 65 dB) acc. CISPR 22 edition 5.2, figure D.3.
    • For up to 4 Pairs UTP
    • Allows to perform common mode disturbance voltage measurements
    • Provides an longitudinal conversion loss of typically 65 dB at the EuT port
    • Allows to measure CAT5 devices
    In Stock
    Request Quote/More Info
    • DC ... 30 MHz Frequency Range
    • 6 dB ±0.2 dB Insertion loss
    • It is part of the measurement setup according to EN 50561-1:2012
    • Is a resistive, unsymmetrical two way splitter with an impedance of 50 Ω
    In Stock
    Request Quote/More Info
    • 9 kHz - 30 MHz
    • T-ISN 150 Ohm Asymmetric
    • BNC Jack 50 Ohm Unsymmetric
    • 2-Wire
    • 400 V
    • 3 A AC
    • CISPR 22 D1/EN55015-2002
    In Stock
    Request Quote/More Info
    • For use with one, two, three, or four unscreened balanced pairs
    • Refers schematic circuit example in CISPR 22/32 Figure D.3/G.3
    • Intended for connection to cable category 3 and 5
    • 1000BaseT and PoE application
    • Changeable pin-arrangements with RJ11 and RJ45

    Purchase Teseq ISN T8

    In Stock
    Request Quote/More Info
    • Purchase Com-Power ISN-T8 here
    • Frequency Range: 150 kHz to 30 MHz
    • For Unshielded Telecomunication Lines 1 to 4 balanced pairs
    • Complies with CISPR 16-1-2, CISPR 22/32
    • Individual Calibration Included
    $410.00
    Typically In Stock
    Request Quote/More Info
    • For use with screened RJ45 connections
    • Up to 8 lines/4 pairs
    • Meets the requirements of CISPR 22, CISPR 32, CISPR 16-1-2
    • Design given in figure D.11 of CISPR 22 and G.11 of CISPR 32
    • Can be used as CDN for IEC 61000-4-6 immunity tests
    In Stock
    Request Quote/More Info
    • For asymmetric disturbance measurements on PLT devices
    • Frequency range 1.6 to 30 MHz
    • LCL >55 dB
    • Conform with EN 50561-1
    • Supplied with Coupling Unit
    $2,460.00
    In Stock
    Request Quote/More Info
    • For use with screened RJ45 connections
    • Up to 8 lines/4 pairs
    • Meets the requirements of CISPR 22, CISPR 32, CISPR 16-1-2
    • Design given in figure D.11 of CISPR 22 and G.11 of CISPR 32
    • Can be used as CDN for IEC 61000-4-6 immunity tests
    In Stock
    Request Quote/More Info
    • For use with screened RJ45 connections
    • Up to 8 lines/4 pairs
    • Meets the requirements of CISPR 22, CISPR 32, CISPR 16-1-2
    • Design given in figure D.11 of CISPR 22 and G.11 of CISPR 32
    • Can be used as CDN for IEC 61000-4-6 immunity tests
    In Stock
    Request Quote/More Info
    • For asymmetric disturbance measurements on PLT devices
    • Frequency range 1.6 to 30 MHz
    • LCL >55 dB
    • Conform with EN 50561-1
    • Supplied with Coupling Unit
    $2,460.00
    In Stock
    Request Quote/More Info
    • For use with screened RJ45 connections
    • Up to 8 lines/4 pairs
    • Meets the requirements of CISPR 22, CISPR 32, CISPR 16-1-2
    • Design given in figure D.11 of CISPR 22 and G.11 of CISPR 32
    • Can be used as CDN for IEC 61000-4-6 immunity tests
    In Stock
    Request Quote/More Info
Showing 13 - 24 of 31 items