Send Enquiry For Newtons4th (N4L) IMP161 Impedance Network for Harmonics & Flicker, Single Phase, 16 A
Newtons4th (N4L) IMP161 Impedance Network for Harmonics & Flicker, Single Phase, 16 A
- 16 Amps RMS
- Single Phase
- Fully Compliant EN/IEC 61000-3-3
Cart 0 Product Products (empty)
No products
TBD Shipping
$0.00 + Shipping Total
Product successfully added to your shopping cart
Quantity
Total
There are 0 items in your cart. There is 1 item in your cart.
Total products
Total shipping TBD
Total + Shipping
Impedance Stabilization Networks (ISN's)
Impedance Stabilization Networks (ISN's)
Impedance stabilization networks (ISN's) are similar to LISN's but used for conducted emissions measurements on signal and data lines. They differ from LISN's in that they can perform Comon-Mode impedance measurements. CISPR 22 and CISPR 32 are common standards requiring the use of an ISN.
ISN's are referred to as an asymmetric artificial network (AAN) in CISPR 16-1-2.
Impedance Stabilization Networks (ISN's) There are 31 products.
Newtons4th (N4L) IMP161 Impedance Network for Harmonics & Flicker, Single Phase, 16 A
In Stock- 16 Amps RMS
- Single Phase
- Fully Compliant EN/IEC 61000-3-3
Newtons4th (N4L) IMP323 Impedance Network for Harmonics & Flicker, Three Phase, 32 A
In Stock- 32 Amps RMS
- Three Phase
- Fully Compliant EN/IEC 61000-3-3
Newtons4th (N4L) IMP753 Impedance Network for Harmonics & Flicker, Three Phase, 75 A
In Stock- 75 Amps RMS
- Three Phase
- Fully Compliant EN/IEC 61000-3-3
Newtons4th (N4L) IMP163 Impedance Network for Harmonics & Flicker, Three Phase, 16 A
In Stock- Use with PPA5531 Power Analyzer for Harmonics & Flicker
- 16 Amps RMS
- Three Phase
- Fully Compliant EN/IEC 61000-3-3
Teseq ISN ST08C Impedance Stabilization Network for Shielded Balanced Pairs
In Stock- For use with screened RJ45 connections
- Up to 8 lines/4 pairs
- Meets the requirements of CISPR 22, CISPR 32, CISPR 16-1-2
- Design given in figure D.11 of CISPR 22 and G.11 of CISPR 32
- Can be used as CDN for IEC 61000-4-6 immunity tests
Com-Power ISN-T2 Impendace Stabilization Network 150 kHz to 30 MHz
Typically In Stock- Frequency Range: 150 kHz to 30 MHz
- For disturbance measurements on a single, unshielded, balanced pair
- Provided with Cat. 3 & Cat. 5 LCL Adapters
- Circuit concept per figure D.1 of EN 55022: 2010+AC:2011 (CISPR 22: 2008, Edition 6.0)
- Meets applicable requirements of EN 55022: 2010+AC:2011 (CISPR 22: 2008, Edition 6.0) and CISPR 16-1-2: 2014, Edition 2.0
FCC CISPR 22 Impedance Stabilization Network (ISN) FCC-TLISN-T4-02
In Stock- Test up to two balanced pair ITE's to CISPR 22
- Frequency Range: 9 kHz - 30 MHz
- Adapters for most Cat 3 and Cat 5 telecom data lines
- Impedance: 150 ± 20Ω
- EUT/AE Connections: D-sub 25 female
- Voltage Division Factor: 9.5 dB ±1 dB
- Max Voltage: 63 VAC RMS, 100 VDC
- Test Voltage: 220 Volts DC
