> Application/Test Type>Conducted Emissions>Impedance Stabilization Networks (Power and Data Lines)>Com-Power ISN-T8 Impendace Stabilization Network and Calibration Kit

Impedance Stabilization Networks (Power and Data Lines)

Quick Links

Information

Viewed products

Com-Power ISN-T8 Impendace Stabilization Network 150 kHz to 30 MHz View larger
Previous Next

Com-Power ISN-T8 Impendace Stabilization Network and Calibration Kit

Used


  • Rent the Com-Power ISN T8 here.
  • Frequency Range: 150 kHz to 30 MHz
  • For Unshielded Telecomunication Lines 1 to 4 balanced pairs
  • Complies with CISPR 16-1-2, CISPR 22/32
  • Individual Calibration Included

More details

Typically In Stock

Request Quote

Request Quote/More Info

Specifications

Voltage Rating50 VDC / 32 VAC (line to ground @ 50/60 Hz)
Frequency Range150 kHz to 30 MHz
Standards MetCISPR 16-1-2, CISPR 22/32
RF Connector50Ω N-type (female)
Mains & EUT ConnectionsD-sub 25 pin female connectors
Current Rating800 mA (per line), 1.6 Amps (per pair)
Isolation150 kHz to 1.5 MHz: 35 to 55 dB 1.5 MHz to 30 MHz: 55 dB
Dimensionssee photo in images
Weight1.4 lbs. (0.6 kg) [ISN + LCL Adapter + Connecting Adapter]

Test Equipment Description

Com-Power ISN-T8 Details:

The Com-Power ISN T8 design is based on the circuit illustrated in Figure D.3 of CISPR 22 and Figure F8 of CISPR 32.
The RF Port is a 50 Ohm female BNC connector, located on the top of the ISN. The ISN is equipped with two D-sub 25 pin female connectors located on the front panel (EUT Port) and rear panel (AE Port), providing the interface to the LCL Adapter and Connecting Adapter, respectively.

Com-Power ISN-T8 Specifications:

  • Standards: CISPR 16-1-2, CISPR 22, CISPR 32
  • Frequency Range: 150 kHz to 30 MHz
  • Application: Unscreened lines w/up to 4 balanced pairs
  • Max. Current rating: 800 mA (per line), 1.6 Amps (per pair)
  • Voltage rating: 50 VDC / 32 VAC (line to ground @ 50/60 Hz)
  • RF Port Connector: 50O BNC (female)
  • EUT/AE Port Connections: RJ45 (RJ11 also available)
  • Common mode Impedance: 150O ±20 Ohms
  • Phase: 0° ±20°
  • Voltage Division Factor: 10.5 dB ±1 dB
  • Decoupling Attenuation(minimum Isolation)
  • 150 kHz to 1.5 MHz: 35 to 55 dB
  • 1.5 MHz to 30 MHz: 55 dB
  • Symmetric Insertion Loss: Max: 3 dB ±0.25 dB
  • Symmetric Load Impedance: 100O
  • Transmission Bandwidth: >100 MHz
  • Weight: 1.4 lbs. (0.6 kg) [ISN + LCL Adapter + Connecting Adapter]

Com-Power ISN Calibration Kit Includes:

1Balance TransformerISN-BT-T248
1BT Calibration Load BlockISN-CLB-BT
210 dB AttenuatorATTN-10-T248
250Ω to 150Ω AdapterADA-515-T248
1RJ45 Pair 1 Adapter (4-pair system)ISN-T8-P1-RJ45
1RJ45 Pair 2 Adapter (4-pair system)ISN-T8-P2-RJ45
1RJ45 Pair 3 Adapter (4-pair system)ISN-T8-P3-RJ45
1RJ45 Pair 4 Adapter (4-pair system)ISN-T8-P4-RJ45
1RJ45 Pairs 1-4 100Ω AE Terminations (4-pair system)ISN-T8-100-RJ45
2RJ45 to BNC Common Mode AdapterISN-ADA-T248-RJ45

Pack content

  • Quick view
    1 x

    • Rent the Com-Power ISN T8 here.
    • Frequency Range: 150 kHz to 30 MHz
    • For Unshielded Telecomunication Lines 1 to 4 balanced pairs
    • Complies with CISPR 16-1-2, CISPR 22/32
    • Individual Calibration Included
    Request Quote
    Typically In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    1 x
    • Measurements for common mode impedance, phase angle, voltage division factor, decoupling attenuation (isolation) and longitudinal conversion loss (LCL)

    • A step-by-step procedure, including test setup diagrams is provided with the calibration kit

    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare

Associated EMC Test Equipment

30 other products in the same category: