Impedance Stabilization Networks (Power and Data Lines)

Quick Links

Information

Viewed products

Teseq ISN T800S...
For use with one, two, three, or four...

Teseq ISN T800S Impendace Stabilization Network per CISPR 22/32 Figure D.3/G.3

View larger

Teseq ISN T800S Impedance Stabilization Network per CISPR 22/32 Figure D.3/G.3

Condition Used

For use with one, two, three, or four unscreened balanced pairs
Refers schematic circuit example in CISPR 22/32 Figure D.3/G.3
Intended for connection to cable category 3 and 5
1000BaseT and PoE application
Changeable pin-arrangements with RJ11 and RJ45

The EMC Shop

More details

In Stock

Request Quote

Request Quote/More Info

Send to a friend
Send to a friend
Teseq ISN T800S Impedance Stabilization Network per CISPR 22/32 Figure D.3/G.3
For use with one, two, three, or four unscreened balanced pairs
Refers schematic circuit example in CISPR 22/32 Figure D.3/G.3
Intended for connection to cable category 3 and 5
1000BaseT and PoE application
Changeable pin-arrangements with RJ11 and RJ45
Recipient :
Name of your friend ^* :
E-mail address of your friend ^* :
^* Required fields
or Cancel
Print

Specifications

Voltage Rating	63 VAC 100 VDC
Frequency Range	150 kHz to 30 MHz
Standards Met	CISPR 16-1-2, CISPR 22/32
RF Connector	50Ω N-type (female)
Mains & EUT Connections	RJ11 and RJ45
Current Rating	600 mA (per line), 1.2 Amps (per pair)
Isolation	Cat 3 - 150 kHz to 30 MHz: 39.3 to 55 dB Cat 5 - 150 kHz to 2 MHz: 65 dB Cat 5 - 2 MHz to 30 MHz:: 49.3 dB to 65 dB
Dimensions	see photo in images
Weight	1.2 lbs. (0.55 kg)
Connectors	105 x 65 x 110 mm

Test Equipment Description

Impedance stabilization networks (ISN, or with CISPR 16-1-2 called AAN: asymmetric artificial network) are defined for measuring of conducted common mode disturbances at information technology equipment (ITE) as required in CISPR 22 and CISPR 32. The ISN is placed between the equipment under test (EUT) and auxiliary equipment (AE) or load which are necessary for the operation of the EUT. The ISN establishes the common-mode termination impedance for the EUT’s telecommunications port during measurement and emulates the unsymmetrical contribution (longitudinal conversion loss, LCL) of the connected line. Different ISNs are available in relation to the line category, line numbers and pin-arrangement.

The Teseq ISN T800S is designed for measurements on up to four unscreened single balanced pairs and consists of one basic network (ISN T800) with D sub 25 connectors and special adapter sets. A set of adapters consists of two pieces of LCL adapters to arrange the lines and realize longitudinal conversion loss (LCL)- requirements for the EUT-side in relation to the use cable category (cat. 3, cat. 5) and one piece of connection adapter arranges the lines for the AE-side. Teseq offers two different adapter sets – ADS T800 and ADS T8x0. ADS T800 gives the connection to RJ45 sockets with pin-arrangements of EIA/TIA T568A respectively T568B. The adapter set ADS T8x0 offers changeable pin-arrangements via 1 mm banana connectors for each pin combination of RJ11/RJ45.