Teseq NSG 1007 Programmable AC and DC Power Sources for IEC 61000-3-2 and -3-3

Details:

The Teseq NSG 1007 series sources are high efficiency, lightweight AC and DC power sources which include high performance power analyzers.
With a crest factor of up to 5:1, the NSG 1007 series sources can drive difficult nonlinear loads with ease. Since many modern products use switching power supplies, they have a tendency to draw high repetitive peak currents. The Teseq sources can deliver a repetitive peak current of up to three times their rated continuous current.
With precise output regulation and accuracy, the sources address many application areas for AC and DC power testing. They provide a high load current capability, multi or single phase output modes, and built-in power analyzer measurements. Additional features including line distortion simulation (LDS), arbitrary waveform generation, and programmable output impedance address requirements for product quality and regulatory compliance testing.

Standards:

• EMC Directives
• EN/IEC 61000-3-2
• EN/IEC 61000-3-3
• IEC/EN 61000-3-11
• IEC/EN 61000-3-12
• IEC/EN 61000-4-8
• IEC/EN 61000-4-11
• IEC/EN 61000-4-13
• IEC/EN 61000-4-14
• IEC/EN 61000-4-17
• IEC/EN 61000-4-27
• IEC/EN 61000-4-28
• IEC/EN 61000-4-29
• IEC/EN 61000-4-34
• MIL STD 461
• RTCA/DO 160

Easy to use controls

The NSG 1007 series sources are microprocessor controlled and can be operated from an easy to use front panel keypad. Functions are grouped logically and are directly accessible from the keypad. This eliminates the need to search through various levels of menus and/or soft keys. A large analogue control knob can be used to quickly slew output parameters. This knob is controlled by a dynamic rate change algorithm that combines the benefi ts of precise control over small parameter changes with quick sweeps through the entire range.

Integrated system

By combining a fl exible AC/DC power source with a high performance power analyzer, the Teseq NSG 1007 sources are capable of handling complex applications that have traditionally required multiple instruments.

High crest factor

With a crest factor of up to 5:1, the NSG 1007 series sources can drive diffi cult nonlinear loads with ease. Since many modern products use switching power supplies, they have a tendency to draw high repetitive peak currents. The Teseq sources can deliver a repetitive peak current of up to 3 times their rated continuous current.

Applications

With precise output regulation and accuracy, the sources address many application areas for AC and DC power testing. They provide a high load current capability, multi or single phase output modes, and built-in power analyzer measurements. Additional features including line distortion simulation (LDS), arbitrary waveform generation, and programmable output impedance address requirements for product quality and regulatory compliance testing.

Models Available

• NSG 1007-3-240 Single phase 3 kVA (208 – 240 V) programmable AC and DC Power Source
• NSG 1007-5-208 Single phase 5 kVA (208 V) programmable AC and DC Power Sources
• NSG 1007-5-400 Single phase 5 kVA (400 V) programmable AC and DC Power Sources
• NSG 1007-10-208 Three phase 10 kVA (208 V) programmable AC and DC Power Sources
• NSG 1007-10-400 Three phase 10 kVA (400 V) programmable AC and DC Power Sources
• NSG 1007-15-208 Three phase 15 kVA (208 V) programmable AC and DC Power Sources
• NSG 1007-15-400 Three phase 15 kVA (400 V) programmable AC and DC Power Sources
• NSG 1007-30-208 Three phase 30 kVA (208 V) programmable AC and DC Power Sources
• NSG 1007-30-400 Three phase 30 kVA (400 V) programmable AC and DC Power Sources
• NSG 1007-45-208 Three phase 45 kVA (208 V) programmable AC and DC Power Sources
• NSG 1007-45-400 Three phase 45 kVA (400 V) programmable AC and DC Power Sources

Steady state output control (all parameters)

• Create, run, save, reload and print transient programs
• Generate and save harmonic waveforms
• Generate and save arbitrary waveforms
• Download data from a digital storage oscilloscope
• Measure and log standard measurements
• Capture and display output voltage and current waveforms
• Measure, display, print and log harmonic voltage and current measurements
• Run IEC 61000-4-11, IEC 61000-4-14 and IEC 61000-4-28 test programs
• Display IEEE-488 or RS232C bus traffic to and from the AC source to help develop your own test programs
• Requires PC running WindowsXP™ or Windows 2000™ or Windows Vista™