> Compliance Standards>Military & Aerospace Standards>MIL-STD-461
MIL-STD-461

Test equipment for all versions of MIL-STD-461 including Version G released Decemeber 2015.

MIL-STD-461 Emission and Susceptibility Testing Breakdown

Conducted emissions requirements are designated by CE

Radiated emissions requirements are designated by RE

Conducted susceptibility requirements are designated by CS

Radiated susceptibility requirements are designated by RS

Get Application Support, Pricing, Lead Time and More: Contact Form

MIL-STD-461 There are 134 products.

Subcategories

  • Radiated Susceptibility

    MIL-STD-461 Radiated Susceptibility Description:

    The EMC Shop stock a variety of MIL-STD-461 Radiated Susceptibility test equipment for Magnetic Field, Electric Field, and Transient Electromagnetic Field applications.

    Get Application Support, Pricing, Lead Time and More: Contact Form

  • Conducted Susceptibility

    The EMC can provide test eqipment for subcategories of MIL-STD-461; Conducted Susceptibility with applications for:

    Power Leads, Antenna Port, Intermodulation, Rejection of Undesired Signals, Cross-Modulation, Structure Current, Bulk Cable Injection, Impulse Excitation, Damped Sinusoidal Transients, Cables and Power Leads, Lightning Induced Transients, and Personnel Borne Electrostatic Discharge

    Get Application Support, Pricing, Lead Time and More: Contact Form

  • Radiated Emissions

    The EMC Shop stocks and delivers a wide array MIL-STD-461 Radiated Emissions equipment. Applications include: Magnetic Field, Electric Field,Antenna Spurious and Harmonic Outputs.

  • Conducted Emissions

    MIL-STD-461 conducted emission testing equipments for power leads, antenna terminals and more. The EMC Shop carries a variety of testing equipment for all MIL-STD-461 compliance tests.

    The conducted emissions testing for MIL-STD-461 is similar to DO-160 Conducted Emissions testing.

    CE101 Applicability

    MIL-STD-461 CE101 requirement is applicable for power leads, including returns, that obtain power from other sources not part of the EUT.

    For AC applications, this requirement is applicable starting at the second harmonic of the EUT power frequency.

    CE101 Test Procedure

    This test procedure is used to verify that electromagnetic emissions from the EUT do not exceed the specified requirements for power input leads including returns. 5.4.3.2 Test equipment. The test equipment shall be as follows:

    a. Measurement receivers

    b. Current probes

    c. Signal generator

    d. Data recording device

    e. Oscilloscope

    f. Resistor (R)

    g. LISNs

per page
Showing 97 - 108 of 134 items
  • Quick view
    • RTCA DO-160 Section 22 Compliant
    • Mains supply coupling unit For W4, W5A, W5B surge wave coupling
    • Isolation AC/DC supply max.400V
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Waveform Output:
      • W2
      • W3
      • W6
    • PIN Injection Test
    • Cable Bundle Test (single stroke & multiple stroke)
    • RTCA DO-160 Section 22 Compliant
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • One-box transformer and 0.5 ohm load assembly
    • Frequency response 10 Hz to 250 kHz
    • Secondary saturation 50 A per transformer
    • Audio power 2 x 200 W
    • Freely configurable on primary/secondary; serial, parallel, single
    • Turns ratio 2:1 step down
    • Built-in non-inductive load resistor 0.5 ohm, 250 W
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • for Test Method RE101 of MIL-STD-461F
    • Required by Test Method RE01 in Parts 2 through 6 of MIL-STD- 461C and
    • RE101 of MIL-STD-461D/E/F
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Transmit/Receive Loop Antenna Set for MIL-STD-461, RS101 Calibration/Test 
    • Frequency Range: 30 Hz to 100 kHz 
    • Convenient, Fixed Mounting Arrangement for Receive Loop onto Transmit Loop for Accurate Calibration of Test Levels 
    • Three-year Standard Warranty
    Request Quote
    In Stock
    Request Quote/More Info
    Add to Compare
Showing 97 - 108 of 134 items