> EMC Test Equipment>Transient Generators>Automotive Transient Immunity Generators>EM Test AMP 200N Low Frequency Signal Source DC (0Hz) to 250kHz

Automotive Transient Immunity Generators

Quick Links

Information

Viewed products

EM Test AMP 200N Low Frequency Signal Source DC (0Hz) to 250kHz View larger

EM Test AMP 200N Low Frequency Signal Source DC (0Hz) to 250kHz

New

  • Built-in DDS to generate sinusoidal signals up to 250kHz
  • Built-in LF amplifier, 250W
  • Output voltage max. 140V p-p, 50V rms
  • Output current max. 5A rms
  • Programmable DC voltage offset
  • Controlled by AutoWave and autowave.control via Framebus
  • Integrated voltage measurement 10Hz - 250kHz (optional)
  • Integrated field strength measurement (optional)

More details

Request Quote

Request Quote/More Info

PDF Downloads

EM Test AMP 200N Data Sheet

PDF Downloads (1.49M)

Specifications

Supply Voltage115 V +10/-02%, 50/60 Hz or 230 V +10/-15%, 50/60 Hz
Amplifiers
low-frequency signal source with amplifier
ParameterValue
Operating Temperature10°C - 40°C
Frequency rangeDC - 250kHz
Signal power250W (nominal)
Output voltage50Vrms, max. 140V(p-p) up to 100kHz 30Vrms 100kHz - 250kHz
Output currentMax. 5Arms up to 200kHz Max. 4Arms 200kHz - 250kHz
Output Impedance30 mOhm @ 1 kHz
Harmonic Distortion (THD)less than 0.1%
Protection- Short circuit - Overtemperature
General Data
Technical Details
ParameterValue
Dimensions19", 3HU (500mm x 449mm x 133mm)
WeightApprox. 18kg

Test Equipment Description

EM Test AMP 200N Application:

AMP 200N - Low-frequency signal source for supply simulation and magnetic field testing

The AMP 200N has been designed as a low-frequency signal source to generate sinusoidal signals used to simulate ripple noise and ground shift noise as required by a variety of standards in the automotive industry e.g. as per Ford EMC-CS-2009.1, CI 210 and CI 250 as well as RI 150. The AMP 200N is controlled by the EM TEST Autowave to also allow the generation of non-sinusoidal and customised signals. Additionally, the AMP 200N can be used to generate magnetic fields by means of a radiation loop or small Helmholtz coils as per RI 140 of Ford EMC-CS-2009.1.

Standards

  • Chrysler CS-11809 (2009)
  • Chrysler CS-11979
  • Chrysler DC-11224 Rev.A
  • DaimlerChrysler DC-10615
  • DaimlerChrysler DC-11224
  • Ford EMC-CS-2009.1
  • GMW 3172
  • Jaguar JLR-EMC-CS V1.0 Amd 4
  • MAN 3285
  • SAE J1113-2
  • Tata TST/TS/WI/257
           

Benefits

AMP 200N - Signal generator/amplifier solution for ripple noise and magnetic field testing

The AMP 200N unifies a low-frequency signal generator and a powerful amplifier module giving a maximum amplitude of 150V peak-to-peak as required e.g. by Ford EMC-CS-2009.1. It generates both sinusoidal and transient signals. Equipped with a DDS it generates any sinusoidal signal with a frequency up to 250kHz. The AMP 200N is controlled by the EM TEST AutoWave in order to generate any sinusoidal or non-sinusoidal/transient signals and is therefore fully supported by the autowave.control software with its exhaustive library of pre-programmed standards and its outstanding reporting and documentation capabilities.

The AMP 200N can also be used for magnetic field testing using a Radiation Loop and Loop Sensor. Extended by the optional measuring module the AMP 200N offers means for frequency-selective current measurement, voltage measurement and measurement of the magnetic field strength.
Optional Product:
EM Test AMP 200N1.1 - High frequency option up to 500 kHz
           

30 other products in the same category: