Conducted Emissions

Quick Links

Information

Viewed products

Teseq LNA 6000 Low Noise Amplifier 1 MHz to 3 GHz View larger

Teseq LNA 6000 Low Noise Amplifier 1 MHz to 3 GHz

New

  • Frequency range: 1 MHz to 3 GHz (nominal range);200 kHz to 4 GHz (utilizable range)
  • Gain: typ. 12.5 dB
  • Gain flatness: ±0.3 dB (1 MHz to 1 GHz); +0.3 / -2.5 dB (200 kHz to 3 GHz)
  • RF-Input: N - female, 50 Ω
  • RF-Output: N - male, 50 Ω
  • VSWR (input): ≤1.5
  • Noise figure: typ. 4 dB
  • 1 dB-compression (output): >+12.5 dBm (119.5 dBμV)

More details

Request Quote/More Info

Specifications

Frequency Range1 MHz to 3 GHz (nominal range) 200 kHz to 4 GHz (utilizable range)
RF ConnectorIN: N-type (f); OUT: N-type (m)
Gain12.5 dB (±0.3 dB flatness)
Application/Test TypeIncrease the sensitivity of virtually all spectrum analyzers and other RF measuring instruments.
Input0 dBm (107 dBμV)
Maximum Continuous Power12.5 dBm @ 1 dB compression
Dimensions28 mm x 95 mm x 27 mm
Weightapprox. 127 grams (0.3 Lb's)

Test Equipment Description

The Teseq LNA 6000 is a low noise amplifier with 12.5 dB of gain covering the nominal frequency range 1 MHz to 3 GHz and can be used in the range from 200 kHz to 4 GHz. With its high gain and low noise figure, it will significantly increase the sensitivity of virtually all spectrum analyzers and other RF measuring instruments.
All measuring instruments have a ‘noise figure’, which is a measure of how good the instrument is at measuring low level signals, the lower this figure, the better, although the lowest signal level will still be governed by the measurement bandwidth. A typical spectrum analyzer may have a noise figure of 20 dB or more, whereas a typical receiver may have a noise figure of 10 dB. The preamplifier has a noise figure of typically 4 dB, significantly enhancing the low level performance of such instruments, enabling signals that were previously masked by noise to be seen.

The low noise amplifier can be connected directly to the RF input (N) of the spectrum analyzer or EMI-receiver. If the LNA 6000 is used with the Teseq receiver SCR 35xx / SMR 45xx, the power supply is provided directly by the receiver via the cable LE 237. Alternatively the power supply unit PSU 6000 can be used.

Features & Specifications of Teseq LNA 6000:

  • Frequency range: 1 MHz to 3 GHz (nominal range);200 kHz to 4 GHz (utilizable range)
  • Gain: typ. 12.5 dB
  • Gain flatness: ±0.3 dB (1 MHz to 1 GHz); +0.3 / -2.5 dB (200 kHz to 3 GHz)
  • RF-Input: N - female, 50 Ω
  • RF-Output: N - male, 50 Ω
  • VSWR (input): ≤1.5
  • Noise figure: typ. 4 dB
  • 1 dB-compression (output): >+12.5 dBm (119.5 dBμV)
  • Intercept point IP3 (output): typ. +33 dBm
  • Max. input (linear): 0 dBm (107 dBμV)
  • DC-power supply: 11 to 15 V
  • DC-current: approx. 61 mA
  • DC-connector: ODU-female, plus on inner conductors
  • Operating temperature range: 0° to 40°C
  • Storage temperature range: -20° to 60°C
  • Size (W x D x H) (without connectors): 27 mm x 50 mm x 27 mm
  • Size (W x D x H) (including connectors): 28 mm x 95 mm x 27 mm
  • Weight: approx. 127 g

Associated EMC Test Equipment

30 other products in the same category: