RF Amplifiers 10kHz - 400 MHz

Quick Links

Information

Viewed products

Amplifier Research 600A225A 10KHz - 225MHz, 600 Watts CW Solid State Amplifier

New

  • 10 kHz - 225 MHz
  • 600 W CW
  • M1 - M9
  • LCD touch screen 
  • Gain control, pulse input capability, RF sample ports
  • LDMOS circuitry

Standards

  • RF Immunity Testing
  • Particle Accelerators
  • Telecommunications
  • Antenna / Component Testing
  • Plasma Generation
  • Watt Meter Calibration

More details

Typically In Stock

Request Quote/More Info

PDF Downloads

Test Equipment Description

The Amplifier Research 600A225A is a self-contained, air-cooled, broadband, completely solid state amplifier designed for applications where instantaneous bandwidth and high gain are required. Push-pull LDMOS circuitry is utilized in all high power stages in the interest of lowering distortion and improving stability. The Model 600A225A, when used with an RF sweep generator, will provide a minimum of 600 watts of swept power.

The Model 600A225A is equipped with a Digital Control Panel (DCP) which provides both local and remote control of the amplifier. The DCP uses a color LCD touch screen and a single rotary knob to offer status reporting and control capability. The display provides operational presentation of Forward Power and Reflected Power plus control status and reports of internal amplifier status. Special features include a gain control, pulse input capability, forward RF sample port, and a reflective RF sample port for precise power measurements.

All amplifier control functions and status indications are available remotely in GPIB/IEEE-488, RS-232, RS-232 fiber optic, Ethernet and USB format. The buss interface connectors are located on the back panel and positive control of local or remote operation is assured by a switch on the front panel of the amplifier. High efficiency universal input, power factor corrected switching power supplies provides DC to all internal subassemblies.

Housed in a stylish, contemporary enclosure, the Model 600A225A provides readily available RF power for typical applications such as RF susceptibility testing, antenna and component testing, watt meter calibration, particle accelerators, plasma generation, communications and use as a driver for higher power amplifiers. The export classification of this equipment is EAR99. These commodities, technology or software are controlled for export in accordance with the U.S. Export Administration Regulations. Diversion contrary to U.S. law is prohibited.

600A225A Typical Power Output

Amplifier Research 600A225A Specifications
RATED OUTPUT POWER600 watts
INPUT FOR RATED OUTPUT1.0 milliwatt maximum
POWER OUTPUT @ 3 dB compressionNominal: 600 watts
Minimum : 550 watts
POWER OUTPUT @ 1 dB compressionNominal: 550 watts
Minimum: 400 watts
FLATNESS± 2.5 dB maximum
FREQUENCY RESPONSE10 kHz–250 MHz instantaneously
GAIN (at maximum setting)58 dB minimum
GAIN ADJUSTMENT (continuous range)20 dB minimum
INPUT IMPEDANCE50 ohms, VSWR 1.5:1 maximum
OUTPUT IMPEDANCE50 ohms, nominal
MISMATCH TOLERANCE100% rated power without foldback up to 6.0:1 mismatch, above which may limit to 300W reflected power. Will operate without damage or oscillation with any magnitude and phase of source and load impedance.
MODULATION CAPABILITYWill faithfully reproduce AM, FM, or pulse modulation appearing on the input signal
HARMONIC DISTORTIONMinus 20 dBc maximum at 400 watts
THIRD ORDER INTERCEPT POINT65 dBm typical
RF POWER DISPLAY0–750 watts full scale
PRIMARY POWER180–264 VAC 47–63 Hz, 2500 watts maximum @ 0.99 P.F. typical
CONNECTORS
RF inputType N female, front
RF outputType N female, front
Forward SampleBNC female on front panel (coupling factor 60 dB typical)
Reverse SampleBNC female on front panel (coupling factor 60 dB typical)
Pulse Modulation InputBNC female on rear panel
Safety Interlock15 pin female Type D on rear panel
REMOTE CONTROL
IEEE-48824-pin female on rear panel
RS-2329 pin female Type D on rear panel
RS-232 (Fiber optic)Type ST on rear panel
USBType B female on rear panel
EthernetRJ-45
COOLINGForced air (self-contained fans)
WEIGHT, maximum45.8 kg (101 lb)
SIZE (W x H x D)50.3 x 34 x 56.9 cm19.8 x 13.4 x 22.0 in
EXPORT CLASSIFICATIONEAR99

Associated EMC Test Equipment

18 other products in the same category: